+86-028-85255257
1x9-155M-20km transceiver
1.Feature
2.Application
3.Description
The1×9 transceiver supports 155Mbps and 20Kmtransmission distance with SMF.
The transceiver consists of two sections: Thetransmitter section incorporates a FP laser. thereceiver section consists of a PIN photodiodeintegrated with a trans-impedance preamplifier (TIA).
4.Performance specifications
4.1Absolute Maximum Ratings
Parameter |
Symbol |
Minimum |
Maximum |
Units |
Storage Temperature |
Tst |
-40 |
+85 |
°C |
Operating Temperature |
Top |
0 |
+70 |
°C |
Supply Voltage |
Vcc |
0 |
+5 |
V |
Input voltage |
Vin |
GND |
Vcc |
|
Lead Soldering Temperature & Time |
240/10 |
°C/s |
4.2Operation Environment
Parameter |
Symbol |
Minimum |
Maximum |
Units |
Supply Voltage |
Vcc |
4.5 |
5.5 |
V |
Ambient operating Temperature |
Top |
0 |
+70 |
°C |
Operating Relative Humidity |
- |
5 |
95 |
% |
4.3Transmitter Section
(Ambient Operating Temperature 0°C to +70°C, Vcc =5.0 V)
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Units |
Data rate |
- |
- |
155 |
- |
Mb/s |
Center Wavelength |
lo |
1260 |
1310 |
1360 |
nm |
Output Spectral width |
Dl |
- |
- |
4 |
nm |
Average Optical Output Power |
Po |
-15 |
- |
-3 |
dBm |
Extinction Ratio |
Er |
12 |
- |
18 |
dB |
Rise/Fall Time(20%~80%) |
Tr/Tf |
0.26 |
ns |
||
Total jitter |
Tj |
0.43 |
UI |
||
Optical Eye Diagram |
IEEE 802.3u and ANSI Fibre Channel Compatible |
||||
Input differential impendence |
Zdiff |
100 |
Ohm |
4.4Receiver Section
(Ambient Operating Temperature 0°C to +70°C, Vcc =5.0 V)
Parameter |
Symbol |
Min. |
Typ. |
Max. |
unit |
Data rate |
155 |
Mb/s |
|||
Wavelength |
l |
1260 |
1620 |
nm |
|
Receiver Sensitivity |
Rsen |
- |
-34 |
dBm |
|
Receiver Overload |
Rov |
-3 |
|||
Output differential impendence |
Zdiff |
100 |
Ohm |
||
LOSS Thresholds |
LOSSD |
- |
- |
-34 |
dBm |
LOSSA |
-45 |
5.Pin Description
Pins |
Name |
Discription |
NOTE |
1 |
VeeR |
Receiver Ground |
|
2 |
RD+ |
IReceived Data Output (PECL) |
|
3 |
RD- |
Inv.ReceivedData Output (PECL) |
|
4 |
SD |
Signal Detected (PECL) |
|
5 |
VccR |
Receiver Power |
|
6 |
VccT |
Transmitter Power |
|
7 |
TD- |
Inv. Transmit Data Input (PECL) |
|
8 |
TD+ |
Transmit Data Input (PECL) |
|
9 |
VeeT |
Transmitter Ground |
Regulatory Compliance
F-tone Networks Optic transceiver is designed to be Class I Laser safety compliant and is certified per the following standards
Feature |
Agency |
Standard |
Laser Safety |
FDA |
CDRH 21 CFR 1040 annd Laser Notice No. 50 |
Product Safety |
BST |
EN 60825-1:2007 EN 60825-2:2004 EN 60950-1:2006 |
Environmental protection |
SGS |
RoHS Directive 2002/95/EC |
EMC |
CCIC |
EN 55022:2006+A1:2007 EN 55024:1998+A1:2001+A2:2003 |
Ordering information
Part Number |
Product Description |
FT19-1303H-20 |
1x9-sm1310-5V-PECL-SD:PECL-20km-SC |
FT19-1303H-20F |
1x9-sm1310-5V-PECL-SD:PECL-20km-FC |
FT19-1303H-20T |
1x9-sm1310-5V-PECL-SD:PECL-20km-ST |
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must bespecifically confirmed in writing by F-tone Networks before they become applicable to any particular order orcontract. In accordance with the F-tone Networks policy of continuous improvement specifications may changewithout notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.